• 公司相册
  • 公司形象
  • 公司活动
  • 产品发货
  • 产品包装
  • 客户来访
  • 车间生产现场
  • 施工安装现场
  • 海外市场
  • 新闻中心
  • 联系我们
  • 咨询留言
  • 翻板阀、锁风阀、卸灰万博体育max网页版注册
    钟形卸灰阀

    本系列钟形卸灰阀广泛适用于冶金、建材、石化、电力等行业,作为各工业炉窑及除尘系统的卸灰装置。

    This series valve is widely used in metallurgy, building material, oil chemical and electric power industries etc. It is the discharging device of stove and removing dust system.

     

    结构特点:

    Structure characteristic:

    该钟形卸灰阀由阀体、锥形阀塞、连杆、驱动装置等组成,用连杆拉动阀塞上下运动完成启闭动作。其中X型为橡胶软密封,应用于冶炼高炉喷煤系统的煤粉输送控制。W型为阀体本体材料密封,应用于除尘系统尘灰输送控制。

    This valve is made up of body, cone valve plug, connected pole, driving device etc. The plug drew by the connected pole moves up and down to complete the action of open and close. Type X denotes rubber soft seal, which is applied to carrying control of coal powder in smelt blast furnace gushing coal system. Type W denotes body material seal, which is applied to carrying control of dust powder in removing dust system.

     

    性能参数:

    Performance parameter:

    公称压力

    Nominal pressure

    0.4MPa

    适用温度

    Suitable temperature

    80150

    密封试验压力

    Seal test pressure

    0.44MPa

    强度试验压力

    Strength test pressure

    0.6MPa

    适用介质

    Suitable medium

    含煤气尘灰、烟气尘灰煤粉等干燥细粉物料

    Dust with coal gas and smoke, dry powder

     

    工作原理:

    Working principle:

    手动钟形卸灰阀利用力矩平衡的方法实现卸灰。当作用于锥形塞上的物料产生的力矩大于重锤摇杆产生的力矩时,锥形塞打开向下卸灰。一旦积灰卸去后,重锤与摇杆产生的力矩使锥形塞迅速关阀。落料的频率及卸灰量依据工况需要来调整重锤位置。

    执行机构得到程序指令后推动摇杆使锥形塞打开向下卸灰,积灰卸去后,依据程序规定时间,推杆推进使锥形塞关闭密闭。执行机构的推出与推进都有行程控制,同时反馈开关信号。

    The valve realizes discharging using trimming moment. When the moment made by material on cone plug is greater than that of heavy hammer and rocker, the plug will open adown to discharge. After discharge the moment made by heavy hammer and rocker will drive cone plug close quickly. Dropping material frequency and discharge amount is determined by the working condition demand to adjust heavy hammer position.

    Actuator drives the rocker after receives program order, and the rocker drives the plug open adown to discharge dust. Draw stem drives the plug to close according to the program time after discharge. Push and extrusion of actuator are controlled by journey and feed back switch signal at the same time.

    XH--- X W系列外形连接尺寸:

    Appearance joint dimension:

    DN

    200

    250

    300

    350

    400

    450

    500

    600

    700

    800

    D

    370

    420

    480

    530

    620

    670

    720

    835

    935

    1055

    D1

    330

    380

    440

    490

    570

    620

    670

    780

    880

    990

    D2

    280

    330

    380

    430

    500

    550

    600

    700

    800

    900

    D3

    390

    440

    500

    550

    650

    700

    750

    865

    965

    1083

    D4

    350

    400

    460

    510

    600

    650

    700

    810

    910

    1020

    D5

    240

    290

    340

    390

    450

    500

    550

    650

    750

    850

    H

    350

    400

    450

    500

    550

    600

    640

    680

    730

    760

    H1

    480

    530

    580

    630

    680

    730

    770

    810

    860

    890

    L1

    755

    805

    855

    925

    975

    1025

    1075

    1275

    1375

    1475

    L2

    740

    790

    840

    910

    960

    1010

    1060

    1200

    1300

    1400

    n-d

    8-Φ18

    12-Φ18

    12-Φ22

    12-Φ22

    16-Φ22

    16-Φ22

    20-Φ22

    20-Φ26

    24-Φ26

    24-Φ30

    电动推杆

    Electric draw stem

    DTA25-M

    P0.025kw

    DTA63-M

    P0.06kw

    DTA100-M

    P0.25kw

    气动推杆

    Pneumatic   draw stem

    10A-5TCC32B

    10A-5TCC40B

    10A-5TCC50B

     

    使用说明:

    Operation instruction:

    l  安装时请注意闸门本体上标明介质流向,清除内腔附着物。两法兰连接时必须加密封垫片,然后均匀锁紧螺栓。

    l  设备在运行时,请定期给传动部分加润滑油。执行部分定期维护和检修。

    l  若长期存放应使设备处于关闭状态,各传动部位加润滑油,不允许露天存放或堆置。

    l   Pay attention to the direction of medium in valve body. Clean the inner body. Add seal cushion between two flanges connection and screw down bolt

    l   Please add lubricant to transmission when equipment is operating and maintain and check the actuator regularly.

    l   Add lubricant to transmission part when valve is long stored. It should not be placed or piled up in the open air.


  • 上一条信息:扇形闸门-2型
  • 下一条信息:锥形锁风阀
  • 湖北万博全站app官方下载环保成套设备有限公司 版权所有

    备案号: 鄂ICP备14001966号-1

    地址:湖北省荆州市沙市区十号路98号 电话:0716-4302555 传真:0716-4310988